Ford 8N Tractor Parts
Online Catalog has Ford 8N Tractor Parts descriptions, pictures, and prices.
Click on the Image below to enter the Online Catalog.

 Ford 8N Tractor Parts Catalog
Tractor Parts Catalog

Clutch Parts Cooling Systems Engine Overhaul Kit
Engine Parts Filters Front Axle Steering Parts
Hitch & Drawbar Parts Hydraulic System Parts Ignition & Electrical Parts
Lights & Related Parts Manuals Mufflers Exhaust Pipes
PTO Parts Rims & Wheels Seats
Sheet Metal & Related Parts Transmission & Rear Axle  

The Ford 8N tractor was built in Dearborn, Michigan in 1947. This continued production into 1953 at which time over half of one million were built- five hundred and twenty four hundred thousand (524,000).

Aftermarket Ford 8N tractor parts are available for almost the entire tractor. Clutch parts are flywheel bearings, pressure plates (either the 10 inch or the 9 inch plate), release bearings and the 9 inch spring loaded transmission disc.
The cooling system parts include fan belts, fan blades, water pump with gasket, radiator and hoses, and a 180 degree thermostat.

The Ford 8N tractor parts for engines are for the 120 CID gas engine.  The engine overhaul kit includes pistons, liners, rings (available in 0.04 and 0.09 three and four ring) bearing sets, con rod sets (both available in standard, 0.002, 0.010, 0.020, 0.030, and 0.040 oversized) and a complete gasket set with seals.  Good used long block, short blocks, cylinder heads, connecting rods and oil pans are available.

Other ford 8n tractor parts for the engine are Marvel Schebler carburetors and kits, oil pressure gauge, manifold, oil pump repair kit, and valve train parts.

The Ford 8N Tractor fuel tank has a capacity of ten (10) gallons or 37.9 US liters. The hydraulic system has a capacity of five (5) gallons or 18.9 US liters. The motor oil used will depend on the operating temperatures .At 30 degrees Celsius, SAE 30 is used, at 0-30, SAE 20, from -12 to 0, 20W and below -12 degrees, 10W is used.  Motor oil capacity is six (6) quarts, or 5.7 US liters.

The sparkplug ignition gasoline engine uses a sparkplug gap of 0.025.

The transmission is a four (4) forward and single reverse constant mesh transmission uses twenty (20) quarts of transmission oil. This oil is either the SAE 90 or the SAE 80. The tractor’s speed will vary according to the rpm of the engine, which ranges typically between 1500 rpm and 1750 rpm.  Ford 8N tractor parts for the transmission includes bearing cones, bearing cups, brake shoes (drum type), countershaft gears, differential pinion cone, and first, second, third, fourth, and reverse gear. Brand new front hubs (part number 8N1171) and oil seals are also available for sale aftermarket.

The hydraulic pump for this tractor is the piston type.  Ford 8N Tractor parts for this hydraulic pump include pump PTO shaft, gasket, pump hub, repair kit, pulley, sheave and hydraulic pump shaft drive.

The 12 V alternators come in two variations, one for models before 1951, and the other side mounted alternator for models after 1951. This is sold in a kit that includes alternator, resistor, coil, wiring harness, hardware kit, brackets, pulley and belt.

Mufflers and exhaust Ford 8N Tractor parts vary with the serial number of the machine.  Exhaust pipes can be either horizontal or vertical.  These are also different exhaust pipes depending on if the engine is gas or diesel. Mufflers follow the same pattern, there being different mufflers depening on if the engine of the tractor is diesel or gas. The mufflers are further sub-divided based upon the end connections. These can be flared to different diameters, and some requires muffler clamps.

The Ford 8n tractor parts for PTO include the PTO Assembly. This is 30.81” long, and contains the PTO housing, cover, collar with tapered pin, snap ring, front shaft bearing, seals sleeve, and PTO housing gasket.