Master Parts Catalog

Shop Tractor Parts and Check Stock

Tractor Parts

Tractor Parts Shopping Cart

 
Free Fast Moving Tractor Parts Catalog

Get Free Parts Manual When Tractor Repair Tips is Requested

Connect/Share


Tractor Parts, Ag Parts and Construction Equipment Parts
Promote Your Page Too

Ford Tractor Parts

Ford Tractor Parts

Ford Axle & Steering Parts

Attention: Farmers & Mechanics!!!
Looking for

Ford Tractor Axle & Steering Parts?

You Can Benefit from:

Ford Tractor Wheel Hub

Ford Tractor Wheel Hub

  1. The Largest Online New Aftermarket Parts Store in the USA-95,000 part numbers and growing
  2. Seeing Pictures, Prices, Descriptions, and Availability before you buy
  3. Paying Up to 50% less that Dealer Prices
  4. The lowest freight rates from UPS, DHL, and other couriers.
  5. Call Easy Tractor Parts (1-877-668-7278) or Click the Image Below to Enter the

Ford Tractor Parts Catalog.

Tractor-Parts-Catalog

Ford Tractor Axle and Steering Parts

Ford tractor Axle parts and Ford Tractor steering parts are separated into nine (9) different sections in the tractor parts catalog.

These nine (9) sections are axle related parts, axle & knees, power steering pumps & motors, spindles, steering arms & shafts, steering parts, tie rods & ball joints, wheel bearings, sleeves, wheel hubs and caps.

The axle related parts section will include front wheel hubs and stud bolts, the spindle bearings and bushings, front pivot bushing, hub cap, front wheel nut, radius rod, seal, socket radius ball, socket radius cap, and taper cone bearings.

The knee section will include the front radius rod support bracket, and the front axle support.  One of the major components of the front axle section is the right and left hand side spindles. The Ford 5000 tractor has two sets of spindles for each side. One set of spindles was for 10 x 16 tires, and the other set for tires that are not this size.  The wheel bearing kits are similarity stocked; with two different types of bearings depending on if the tire size is 10 x 16 or not.

The Ford 5000 tractor has three different types of steering arms, one right side and one left side. There is one dual center steering arm for use with power steering tractors that were manufactured in 1970 to 1975.

Other Ford Tractor steering parts will include ball bearing, steering bushings, drag link, cylinder pin, steering shaft, steering wheel and nut, and cylinder repair kit for the power steering cylinder.

The tie rods are of various types and vary with the tractor type. Such differences such as whether the tractor is power steering or manual, or the year of manufacture. Drag link ends are sold separately from the drag kinks assemblies sometimes, as are the tie rod ends.

The front wheel hub for the Ford 5000 tractor are two different six (2) stud bolts  hubs, one for rims that uses 10 x 16 tires, and the other for normal tire sizes.

For power steering tractors, hydraulic lines are used as a part of the steering system. Hydraulic lines and fittings are available for these power steering cylinders and power steering pumps. Hose lengths can vary from sixteen (16) inches, twenty seven (27) inches, to thirty four (34) inches in lengths with various kinds of fittings.

The Ford 4000 tractor has two different steering wheels, one for manual steering and one for power steering.

Your Name (required)

Your Email (required)

Subject

Your Message

Ford Tractor Radiator parts

A tractor cooling system will include a radiator, radiator fan, fan pulley, fan belt, water pump, lower radiator hose, upper radiator hose, clamps, thermostat, water temperature gauge, temperature sensors, and radiator cap, drain faucet, tank heater, engine block heater, gaskets and appropriate coolant.

The ford 5000 tractor has the 134 CID gas engine, 175 CID Diesel engine, 192 CID Gas engine, 201 CID diesel engine, 201 CID gas engine, 233 CID diesel engine, the 256 CID diesel engine, or the 256 CID gas engine, 256 CID Turbo diesel engine, 268 CID non turbocharged engine, 268 CID turbo diesel, 401 CID Diesel engine or the 401 CID Turbo Diesel engine.

All of these vary with the amount of horse power that the engine is capable of, and the type of fuel used.

The Ford Tractor radiator for the 5000 is of two types. These are either with oil cooler or without oil cooler. The earlier models of the tractor were not manufactured with the oil cooler bolted onto the radiator, as were the models after 1965.

The radiator cap can either be a 13 lb or a 7 lb cap pressure. This tractor typically carries a six (6) blade radiator fan.

This Ford tractor radiator water pump can be one of two types-either a water pump with a single groove pulley, or for the tractors manufactured 1965 to 1975, the water pump uses a double groove pulley. The BSD442 engine uses a single pulley without a back housing.

The thermostats can be of three different temperature ratings. Ford tractor radiator for the super Dexta is available for the years 1962 to 1964. For this tractor, there is a 7

Ford Tractor Radiator parts

A tractor cooling system will include a radiator, radiator fan, fan pulley, fan belt, water pump, lower radiator hose, upper radiator hose, clamps, thermostat, water temperature gauge, temperature sensors, and radiator cap, drain faucet, tank heater, engine block heater, gaskets and appropriate coolant.

The ford 5000 tractor has the 134 CID gas engine, 175 CID Diesel engine, 192 CID Gas engine, 201 CID diesel engine, 201 CID gas engine, 233 CID diesel engine, the 256 CID diesel engine, or the 256 CID gas engine, 256 CID Turbo diesel engine, 268 CID non turbocharged engine, 268 CID turbo diesel, 401 CID Diesel engine or the 401 CID Turbo Diesel engine.

All of these vary with the amount of horse power that the engine is capable of, and the type of fuel used.

The Ford Tractor radiator for the 5000 is of two types. These are either with oil cooler or without oil cooler. The earlier models of the tractor were not manufactured with the oil cooler bolted onto the radiator, as were the models after 1965.

The radiator cap can either be a 13 lb or a 7 lb cap pressure. This tractor typically carries a six (6) blade radiator fan.

This Ford tractor radiator water pump can be one of two types-either a water pump with a single groove pulley, or for the tractors manufactured 1965 to 1975, the water pump uses a double groove pulley. The BSD442 engine uses a single pulley without a back housing.

The thermostats can be of three different temperature ratings. Ford tractor radiator for the super Dexta is available for the years 1962 to 1964. For this tractor, there is a 7 lb radiator cap, lower radiator hose, and upper radiator hose. Between the years 1965 to 1975, the Super Dexta Ford tractor uses a water pump with double pulley. For the years 1955 to 1965, the engines use a water pump with a single pulley, regardless if the engine was a gas ror diesel engine.

Some of the Super Dexta’s uses the BSD333 engine, and this water pump is a single pulley without a back housing.

There are two ford tractor radiators for the Super Dexta, depending on if the engine is a three (3) cylinder engine or a four (4) cylinder engine.  The upper radiator hose and the lower radiator hose vary depending on the type of engine used.  The thermostat ranges from 168 degrees to 192 degrees.

Fan belts are available for most models of Ford Tractors.

lb radiator cap, lower radiator hose, and upper radiator hose. Between the years 1965 to 1975, the Super Dexta Ford tractor uses a water pump with double pulley. For the years 1955 to 1965, the engines use a water pump with a single pulley, regardless if the engine was a gas ror diesel engine.

Some of the Super Dexta’s uses the BSD333 engine, and this water pump is a single pulley without a back housing.

There are two ford tractor radiators for the Super Dexta, depending on if the engine is a three (3) cylinder engine or a four (4) cylinder engine.The upper radiator hose and the lower radiator hose vary depending on the type of engine used.The thermostat ranges from 168 degrees to 192 degrees.

Fan belts are available for most models of Ford Tractors.

Ford Tractor Engine Parts

Attention: Farmers & Mechanics!!!
Looking for

Ford Tractor Engine Parts?

You Can Benefit from:

Ford Tractor Engine Parts

Ford Tractor Engine Parts

  1. The Largest Online New Aftermarket Parts Store in the USA-95,000 part numbers and growing
  2. Seeing Pictures, Prices, Descriptions, and Availability before you buy
  3. Paying Up to 50% less that Dealer Prices
  4. The lowest freight rates from UPS, DHL, and other couriers.
  5. Call Easy Tractor Parts (1-877-668-7278) or Click the Image Below to Enter the

Ford Tractor Engine Parts Catalog.

Tractor-Parts-Catalog

Ford Tractor Engine Parts

Ford tractor engine parts are typically divided into engine block components and engine add on parts.

The basic engine block parts are the engine overhaul kit (rebuild kit) which includes the following parts.

A major overhaul kit for ford tractors includes pistons, piston pins, piston pin retainer clips, piston rings, main bearing set, connecting rod (con rod ) bearing set, con rod bushings, camshaft bearings, upper gasket set, lower gasket set, rear and front crankshaft seals.

Main bearing sets are stocked in several oversize options such as 0.10, 0.20, 0.30, and 0.040. Connecting rod bearings are similarly stocked as 0.10, 0.20, 0.30 and 0.40 oversized.

Pistons are available in various oversize also, namely the 0.10, 0.20, 0.30 and 0.40 oversize options.

Ford Tractor Parts for the Cylinder sleeves (liners) are sold separately from the rebuild kit. Ford engines are most times built sleeveless.  This is the phenomenon whereby the piston moved directly in the engine block. As the engine wears out due to normal wear and tear, the repairs to the damaged engine block are typically completed by re-boring the engine block, and pressing in a cylinder sleeve (cylinder liner).  These liners can be either finished or unfinished. The finished liners are more expensive and will require no additional machining; the piston can be fitted directly into the finished sleeve. Unfinished sleeves are used when re-boring the engine block for the sleeves is necessary.  The rebore process is necessary to fit oversize pistons into a used cylinder liner.

Other Ford tractor engine parts includes the camshaft, crankshaft, balancer, oil pump, connecting rod, freeze plug, rocker shaft arm, exhaust manifold, intake manifold, muffler, flywheel, ring gear, fuel injection line, fuel pump, fuel injection pump, pump repair kit, tachometer cable, oil pressure sender, water temperature sender, fuel injector, (simms fuel system ), ford tractor fuel injector (CAV and  Simms), radiator, water pump, lower radiator hose and upper radiator hose.

The oil pump can have a repair kit, or separate parts like the main shaft. Intake and exhaust manifolds are of various types. Some are simple three and four cylinder engine manifolds, and some are combination manifolds with eth intake and exhaust is intertwined. The only issue here is that both need to be changed at the same time.

Ford tractor engine parts for the cylinder head will include intake valve, exhaust valve, valve spring, and valve keeper. Parts such as cam followers, push rods, and valve seals will need to be obtained separately.

Your Name (required)

Your Email (required)

Subject

Your Message

Ford Tractor Radiator parts

A tractor cooling system will include a radiator, radiator fan, fan pulley, fan belt, water pump, lower radiator hose, upper radiator hose, clamps, thermostat, water temperature gauge, temperature sensors, and radiator cap, drain faucet, tank heater, engine block heater, gaskets and appropriate coolant.

The ford 5000 tractor has the 134 CID gas engine, 175 CID Diesel engine, 192 CID Gas engine, 201 CID diesel engine, 201 CID gas engine, 233 CID diesel engine, the 256 CID diesel engine, or the 256 CID gas engine, 256 CID Turbo diesel engine, 268 CID non turbocharged engine, 268 CID turbo diesel, 401 CID Diesel engine or the 401 CID Turbo Diesel engine.

All of these vary with the amount of horse power that the engine is capable of, and the type of fuel used.

The Ford Tractor radiator for the 5000 is of two types. These are either with oil cooler or without oil cooler. The earlier models of the tractor were not manufactured with the oil cooler bolted onto the radiator, as were the models after 1965.

The radiator cap can either be a 13 lb or a 7 lb cap pressure. This tractor typically carries a six (6) blade radiator fan.

This Ford tractor radiator water pump can be one of two types-either a water pump with a single groove pulley, or for the tractors manufactured 1965 to 1975, the water pump uses a double groove pulley. The BSD442 engine uses a single pulley without a back housing.

The thermostats can be of three different temperature ratings. Ford tractor radiator for the super Dexta is available for the years 1962 to 1964. For this tractor, there is a 7

Ford Tractor Radiator parts

A tractor cooling system will include a radiator, radiator fan, fan pulley, fan belt, water pump, lower radiator hose, upper radiator hose, clamps, thermostat, water temperature gauge, temperature sensors, and radiator cap, drain faucet, tank heater, engine block heater, gaskets and appropriate coolant.

The ford 5000 tractor has the 134 CID gas engine, 175 CID Diesel engine, 192 CID Gas engine, 201 CID diesel engine, 201 CID gas engine, 233 CID diesel engine, the 256 CID diesel engine, or the 256 CID gas engine, 256 CID Turbo diesel engine, 268 CID non turbocharged engine, 268 CID turbo diesel, 401 CID Diesel engine or the 401 CID Turbo Diesel engine.

All of these vary with the amount of horse power that the engine is capable of, and the type of fuel used.

The Ford Tractor radiator for the 5000 is of two types. These are either with oil cooler or without oil cooler. The earlier models of the tractor were not manufactured with the oil cooler bolted onto the radiator, as were the models after 1965.

The radiator cap can either be a 13 lb or a 7 lb cap pressure. This tractor typically carries a six (6) blade radiator fan.

This Ford tractor radiator water pump can be one of two types-either a water pump with a single groove pulley, or for the tractors manufactured 1965 to 1975, the water pump uses a double groove pulley. The BSD442 engine uses a single pulley without a back housing.

The thermostats can be of three different temperature ratings. Ford tractor radiator for the super Dexta is available for the years 1962 to 1964. For this tractor, there is a 7 lb radiator cap, lower radiator hose, and upper radiator hose. Between the years 1965 to 1975, the Super Dexta Ford tractor uses a water pump with double pulley. For the years 1955 to 1965, the engines use a water pump with a single pulley, regardless if the engine was a gas ror diesel engine.

Some of the Super Dexta’s uses the BSD333 engine, and this water pump is a single pulley without a back housing.

There are two ford tractor radiators for the Super Dexta, depending on if the engine is a three (3) cylinder engine or a four (4) cylinder engine.  The upper radiator hose and the lower radiator hose vary depending on the type of engine used.  The thermostat ranges from 168 degrees to 192 degrees.

Fan belts are available for most models of Ford Tractors.

lb radiator cap, lower radiator hose, and upper radiator hose. Between the years 1965 to 1975, the Super Dexta Ford tractor uses a water pump with double pulley. For the years 1955 to 1965, the engines use a water pump with a single pulley, regardless if the engine was a gas ror diesel engine.

Some of the Super Dexta’s uses the BSD333 engine, and this water pump is a single pulley without a back housing.

There are two ford tractor radiators for the Super Dexta, depending on if the engine is a three (3) cylinder engine or a four (4) cylinder engine.The upper radiator hose and the lower radiator hose vary depending on the type of engine used.The thermostat ranges from 168 degrees to 192 degrees.

Fan belts are available for most models of Ford Tractors.

Ford Tractor Radiator

Attention: Farmers & Mechanics!!!
Looking for

Ford Tractor Radiator?

You Can Benefit from: The Largest Online New Aftermarket Parts Store in the USA-95,000 part numbers and growing

Ford Tractor Radiator

Ford Tractor Radiator

  1. Seeing Pictures, Prices, Descriptions, and Availability before you buy
  2. Paying Up to 50% less that Dealer Prices
  3. The lowest freight rates from UPS, DHL, and other couriers.
  4. Call Easy Tractor Parts (1-877-668-7278) or Click the Image Below to Enter the

Ford Tractor Parts Catalog.

Tractor-Parts-Catalog

Ford Tractor Radiator

A tractor cooling system will include a radiator, radiator fan, fan pulley, fan belt, water pump, lower radiator hose, upper radiator hose, clamps, thermostat, water temperature gauge, temperature sensors, and radiator cap, drain faucet, tank heater, engine block heater, gaskets and appropriate coolant.

The ford 5000 tractor has the 134 CID gas engine, 175 CID Diesel engine, 192 CID Gas engine, 201 CID diesel engine, 201 CID gas engine, 233 CID diesel engine, the 256 CID diesel engine, or the 256 CID gas engine, 256 CID Turbo diesel engine, 268 CID non turbocharged engine, 268 CID turbo diesel, 401 CID Diesel engine or the 401 CID Turbo Diesel engine.

All of these vary with the amount of horse power that the engine is capable of, and the type of fuel used.

The Ford Tractor radiator for the 5000 is of two types. These are either with oil cooler or without oil cooler. The earlier models of the tractor were not manufactured with the oil cooler bolted onto the radiator, as were the models after 1965.

The radiator cap can either be a 13 lb or a 7 lb cap pressure. This tractor typically carries a six (6) blade radiator fan.

This Ford tractor radiator water pump can be one of two types-either a water pump with a single groove pulley, or for the tractors manufactured 1965 to 1975, the water pump uses a double groove pulley. The BSD442 engine uses a single pulley without a back housing.

The thermostats can be of three different temperature ratings. Ford tractor radiator for the super Dexta is available for the years 1962 to 1964. For this tractor, there is a 7 lb radiator cap, lower radiator hose, and upper radiator hose. Between the years 1965 to 1975, the Super Dexta Ford tractor uses a water pump with double pulley. For the years 1955 to 1965, the engines use a water pump with a single pulley, regardless if the engine was a gas r\or diesel engine.

Some of the Super Dexta’s uses the BSD333 engine, and this water pump is a single pulley without a back housing.

There are two ford tractor radiators for the Super Dexta, depending on if the engine is a three (3) cylinder engine or a four (4) cylinder engine.  The upper radiator hose and the lower radiator hose vary depending on the type of engine used.  The thermostat ranges from 168 degrees to 192 degrees.

Fan belts are available for most models of Ford Tractors.

Your Name (required)

Your Email (required)

Subject

Your Message

Ford Tractor Radiator parts

A tractor cooling system will include a radiator, radiator fan, fan pulley, fan belt, water pump, lower radiator hose, upper radiator hose, clamps, thermostat, water temperature gauge, temperature sensors, and radiator cap, drain faucet, tank heater, engine block heater, gaskets and appropriate coolant.

The ford 5000 tractor has the 134 CID gas engine, 175 CID Diesel engine, 192 CID Gas engine, 201 CID diesel engine, 201 CID gas engine, 233 CID diesel engine, the 256 CID diesel engine, or the 256 CID gas engine, 256 CID Turbo diesel engine, 268 CID non turbocharged engine, 268 CID turbo diesel, 401 CID Diesel engine or the 401 CID Turbo Diesel engine.

All of these vary with the amount of horse power that the engine is capable of, and the type of fuel used.

The Ford Tractor radiator for the 5000 is of two types. These are either with oil cooler or without oil cooler. The earlier models of the tractor were not manufactured with the oil cooler bolted onto the radiator, as were the models after 1965.

The radiator cap can either be a 13 lb or a 7 lb cap pressure. This tractor typically carries a six (6) blade radiator fan.

This Ford tractor radiator water pump can be one of two types-either a water pump with a single groove pulley, or for the tractors manufactured 1965 to 1975, the water pump uses a double groove pulley. The BSD442 engine uses a single pulley without a back housing.

The thermostats can be of three different temperature ratings. Ford tractor radiator for the super Dexta is available for the years 1962 to 1964. For this tractor, there is a 7

Ford Tractor Radiator parts

A tractor cooling system will include a radiator, radiator fan, fan pulley, fan belt, water pump, lower radiator hose, upper radiator hose, clamps, thermostat, water temperature gauge, temperature sensors, and radiator cap, drain faucet, tank heater, engine block heater, gaskets and appropriate coolant.

The ford 5000 tractor has the 134 CID gas engine, 175 CID Diesel engine, 192 CID Gas engine, 201 CID diesel engine, 201 CID gas engine, 233 CID diesel engine, the 256 CID diesel engine, or the 256 CID gas engine, 256 CID Turbo diesel engine, 268 CID non turbocharged engine, 268 CID turbo diesel, 401 CID Diesel engine or the 401 CID Turbo Diesel engine.

All of these vary with the amount of horse power that the engine is capable of, and the type of fuel used.

The Ford Tractor radiator for the 5000 is of two types. These are either with oil cooler or without oil cooler. The earlier models of the tractor were not manufactured with the oil cooler bolted onto the radiator, as were the models after 1965.

The radiator cap can either be a 13 lb or a 7 lb cap pressure. This tractor typically carries a six (6) blade radiator fan.

This Ford tractor radiator water pump can be one of two types-either a water pump with a single groove pulley, or for the tractors manufactured 1965 to 1975, the water pump uses a double groove pulley. The BSD442 engine uses a single pulley without a back housing.

The thermostats can be of three different temperature ratings. Ford tractor radiator for the super Dexta is available for the years 1962 to 1964. For this tractor, there is a 7 lb radiator cap, lower radiator hose, and upper radiator hose. Between the years 1965 to 1975, the Super Dexta Ford tractor uses a water pump with double pulley. For the years 1955 to 1965, the engines use a water pump with a single pulley, regardless if the engine was a gas r\or diesel engine.

Some of the Super Dexta’s uses the BSD333 engine, and this water pump is a single pulley without a back housing.

There are two ford tractor radiators for the Super Dexta, depending on if the engine is a three (3) cylinder engine or a four (4) cylinder engine.  The upper radiator hose and the lower radiator hose vary depending on the type of engine used.  The thermostat ranges from 168 degrees to 192 degrees.

Fan belts are available for most models of Ford Tractors.

lb radiator cap, lower radiator hose, and upper radiator hose. Between the years 1965 to 1975, the Super Dexta Ford tractor uses a water pump with double pulley. For the years 1955 to 1965, the engines use a water pump with a single pulley, regardless if the engine was a gas r\or diesel engine.

Some of the Super Dexta’s uses the BSD333 engine, and this water pump is a single pulley without a back housing.

There are two ford tractor radiators for the Super Dexta, depending on if the engine is a three (3) cylinder engine or a four (4) cylinder engine.The upper radiator hose and the lower radiator hose vary depending on the type of engine used. The thermostat ranges from 168 degrees to 192 degrees.

Fan belts are available for most models of Ford Tractors.

Tractor Radiator

Attention: Farmers & Mechanics!!!
Looking for

Tractor Radiator?

You Can Benefit from: The Largest Online New Aftermarket Parts Store in the USA-95,000 part numbers and growing

  1. Seeing Pictures, Prices, Descriptions, and Availability before you buy
  2. Paying Up to 50% less that Dealer Prices

    Tractor Radiator

    Tractor Radiator

  3. The lowest freight rates from UPS, DHL, and other couriers.
  4. Call Easy Tractor Parts (1-877-668-7278) or Click the Image Below to Enter the

Tractor Parts Catalog.

Tractor Parts Catalog

Tractor Radiator

Allis Chalmers Tractor Radiator Case Tractor Radiator
International Tractor Radiator Farmall Tractor Radiator
Deutz Tractor Radiator David Brown Radiator
Ford Tractor Radiator New Holland Tractor Radiator
John Deere Tractor Radiator Kubota Tractor Radiator
Massey Ferguson Tractor Radiator Ferguson Radiator
Perkins Engine Radiator White Tractor Radiator
Oliver Tractor Radiator Minneapolis Moline Radiator

Your Name (required)

Your Email (required)

Subject

Your Message

Ford Tractor Clutch Parts

Attention: Farmers & Mechanics!!!
Looking for

Ford Tractor Clutch Parts?

You Can Benefit from: The Largest Online New Aftermarket Parts Store in the USA-95,000 part numbers and growing

  1. Seeing Pictures, Prices, Descriptions, and Availability before you buy
  2. Paying Up to 50% less that Dealer Prices

    Ford Tractor Clutch Parts

    Ford Tractor Clutch Parts

  3. The lowest freight rates from UPS, DHL, and other couriers.
  4. Call Easy Tractor Parts (1-877-668-7278) or Click the Image Below to Enter the

Ford Tractor Parts Catalog.

Tractor-Parts-Catalog

Ford Tractor Clutch Parts

There are several kinds of clutches is for Ford tractors.  The Ford 5000 tractor has two kinds of clutches.-a select o speed  and a single clutch.  On the contrary to if the Ford Dexter tractor has a double and single clutch.  The Ford 4000 tractor as street kinds of clutch is, of the double clutch, the single clutches, and other select o speed clutch.

Typical clutch parts for Ford tractors are release bearings, pressure plates, PTO disk, transmission disc, flywheel bearings, clutch release hub bearings, and complete bearing kits.

Ford release bearings can be either sealed, our unsealed.

Ford tractor clutch parts in the form of complete kits will typically include the pressure and transmission discs.

A clutch is comprised of several parts. There is the clutch plate, which is sandwiched between the engine flywheel and pressure plate. The pressure plate comes with springs and fingers (these can be typically three (3) levers or six (6)), and these are designed with different diameters.

Then there are bolts or studs that hold the clutch plate to the pressure plate. Onto this setup, is mounted a diaphragm spring and a throw out bearing. This spring mechanism will be used later in moving the clutch plate into and out of engagement with the engine flywheel.

Over the throw out bearing, diaphragm spring, studs, pressure plate and clutch plate, comes the clutch housing. This ford clutch parts housing encases all of the previously mentioned parts, preventing it from being damaged from external impurities.

However, this clutch housing has an opening in the center, and through that a release fork fits through. This is the release fork that is moved when the manual clutch pedal is pressed.

As an additional protection, a bell housing totally encases all of the above mentioned parts.

Pressure plates   come in a variety of diameters. Some are nine inches (9) in diameters, but there are some with eleven (11), and twelve (12) inches diameter.

Ford transmission discs are in a variety of diameters as well, ranging from eleven (11) inches to thirteen (13) inches for the Ford 4000, 5000 and the Super Dexta tractors.

For a large clutch job, a complete ford clutch kit can be ordered. The typical components of the clutch kit are the pressure plate and the transmission disc. Other parts can be sourced separately.

Transmission discs are typically identified by the number of “pads” that they have. However, many of these discs are circular in shape and not pointed as the padded discs.

Your Name (required)

Your Email (required)

Subject

Your Message

Ford Tractor Engines | New Holland Engines

Ford Tractor Engine

Ford Tractor Engine

A Wide Variety of Ford Engines, and New Holland Engines power tractors, combines, excavators, power units, and harvesters. The Online Catalog contains parts for this list of ford engines, and New Holland Engines.

To search for engine parts, its betters to locate the machine type, and then search for the engine for that machine type.

Ford Tractor Engine Parts | New Holland Engine Parts

Online Catalog has Ford Tractor parts descriptions, New Holland parts, pictures, and prices.
BSD666 M411 7.8L 240 HP
BSD332 M421 7.8L 240 HP
BSD333 M721 6.6L 143 HP
BSD333H N
BSD442 Q
BSD444 104 CID
BSD444H 201 CID Gas
BSD444HT 233 CID Diesel
BSD444T 256 CID Diesel
M321 7.8L 220 HP 256 CID Gas
BSD666T 256 CID Turbo Diesel
BSD666TI 268 CID Non-Turbo Diesel
D 268 CID Turbo Diesel
E 401 CID Diesel
M 401 CID Turbo Diesel
M111 7.8L 188 HP 158 & 175 CID Gas
M121 7.8L 188 HP 158 CID Gas
M311 7.8L 220 HP 172 CID Diesel
192 CID Gas 175 CID Diesel
201 CID Diesel

Your Name (required)

Your Email (required)

Subject

Your Message

Ford Combine Models | New Holland Combine Models

Ford CombineFord New Holland Combines are some of the most revered combines in the farming industry.

This list is a complete list of Ford New Holland Combine Models. New aftermarket parts for all of these models are available for sale.

Ford Combine | New Holland Combine

Online Catalog has Ford Combine parts descriptions, New Holland Combine parts, pictures, and prices.
Click on the Link below to enter the Online Catalog.

Ford New Holland Combine Catalog

CX8030 TF44
CX8040 TF46
CR9040 CX8050 TR70
CR9060 CX8060 TR75
CR9070 CX8070 TR76
CR9080 CX8080 TR85
CR920 CX8090 TR86
CR940 CX820 TR87
CR960 CX840 TR88
CR970 CX860 TR89
CR980 CX880 TR95
CX720 G1841 TR96
CX740 SEVERAL TR97
CX760 TC56 TR98
CX780 TF42 TR99
TX32 1500 962
TX34 620 970
TX36 630 971
TX62 640 972
TX64 8050 973
TX65 8055 974
TX66 8060 975
TX68 8070 980
TX88 8080 985
T96 940 990
1400 960 995

Your Name (required)

Your Email (required)

Subject

Your Message

Ford Industrial Equipment | New Holland Industrial Equipment

Ford New Holland Construction Equipment PartsFord Loader

This page details a complete list of Ford New Holland Construction and Industrial Equipment.
New aftermarket parts for all of these models are available for sale.

Ford New Holland Industrial Construction Equipment

Online Catalog has Ford construction equipment parts descriptions, New Holland construction equipment parts, pictures, and prices.
Click on the Link below to enter the Online Catalog.

Ford Parts Catalog

C185 LB90B
A62 C190 LB95
A625 LB110 LM415A
A64 LB110.B LM430
A66 LB110B LM435A
B110 LB115 LM445A
B110 TIER III LB115.B LM5040
B110B TIER III LB115B LM5060
B115 LB75 LM5080
B115 TIER III LB75.B LM640
B95 LB75B LS190B
B95LR LB75CP LT190B
B95TC LB85 LV80
CL40 LB90 SHERMAN 54
C175 LB90.B TK100A
TK75VA 2244 445C
TK76 225 445D
TK80A 233 450
TK80MA 234 4500
TK85 333 455
TK85M 340A 455C
U80 340B 455D
1800 345C 515
1801 345D 535
1811 3500 540
1821 3550 540A
1841 400C 540B
1871 420 545
1881 445 545A
2130 445A 545C
545D 6500 720
550 655 723
5500 655A 730
555 655C 735
555A 655D 750
555B 655E 7500
555C 675D 755
555D 675E 755A
555E 701 755B
5550 702 765
575D 703 8400
575E 712 8401
650 713

Your Name (required)

Your Email (required)

Subject

Your Message

Ford Compact Tractor Models | New Holland Compact Tractor Models

Ford Compact Tractor Models

Ford Compact Tractors are have been used in many applications.  Many of its counterpart New Holland Compact Tractors are sometimes called “Ford Compact Tractors” by some of its enthusiast.

This is a complete list of Ford Compact Tractor Models, and New Holland Compact Tractor  Models that new aftermarket parts are available for.

Ford Compact Tractor | New Holland Compact Tractor

Online Catalog has Ford Compact Tractor parts descriptions, New Holland Compact Tractor parts, pictures, and prices.
Click on the Link below to enter the Online Catalog.

Ford Compact Tractor Catalog

TC18 TC33 TC45DA
TC21 TC33D TC48DA
TC21D TC33DA TC55DA
TC21DA TC34DA TZ18DA
TC23DA TC35 TZ22DA
TC24D TC35A TZ24DA
TC24DA TC35D TZ25DA
TC25 TC35DA T1010
TC25D TC40 T1030
TC26DA TC40A T1110
TC29 TC40D T1510
TC29D TC40DA T1520
TC29DA TC45 T2210
TC30 TC45A T2220
T2310 1220 1720
T2320 1300 1725
T2330 1310 1900
T2410 1320 1910
T2420 1500 1920
1000 1510 1925
1020 1520 2030
1025 1530 2035
1030 1600 2110
1100 1620 2120
1110 1630 3040
1120 1700 3045
1200 1710 3050
1210 1710O 3415
1215 1715 4055
4060

Your Name (required)

Your Email (required)

Subject

Your Message

Ford Tractor Starter

The Largest Online Inventory of

Ford Tractor Starter

Online Catalog has Starter , descriptions, pictures, and prices.
Click on the Link below to enter the Online Catalog.

Ford Tractor Starter Catalog

New to This Site? Look at this Video Tutorial
on How to Select Tractor Starters


The Ford 4000 Tractor was manufactured in a multiple variety of fuels, engine models and transmission types.Ford Tractor StarterThe engine, for example, can be either diesel fuel, or LP gas. The diesel engine comes as the four (4) cylinder 172CD Diesel engine, or as the three (3) cylinders CID Diesel engine. The diesel engines were a latter addition to the Ford line of tractors, with the earlier models initially manufactured for gas. The gas engines were the four (4) cylinder 172 CID Gas engine, the three (3) cylinders 192 CID Gas engine, and the three (3) cylinder 201 CID gas engine.The starter for the diesel engines are typically larger and more powerful than the smaller gasoline engines, as diesel engines compressions needs to be overcome to initiate the starting process.The starter for the diesel 4000 engines is the 83981923. This is a 10 teeth clockwise (CW) rotation, Lucas Ford Tractor Starter that operates off of 12 volts (V). This one starter can be used on a multitude of machines, including the Ford backhoe 400 series and the 500 series, swather, TW series, 2000, 3000, 4000, 5000, 6000, 7000, 8000 and the 9000 series tractors. This Ford Tractor starter weights in at approximately 29 lbs.In Comparison, for gas engines is the D7NN11001A. This weighs 17.26 lbs, has nine (9) teeth, clockwise (CW) rotation, and operates off of 12 volts (V), and is used on several of the wheel loaders, and a multitude of tractors. The part number  C3NF11002CR is identical in specifications to the D7NN11001A, and is used on similar gas tractors.The third type of Ford Tractor Starter is the C3NF11002DR, which is used with six (6) volts (V) systems. The specifications are 9 teeth starter drive and clockwise rotation (CW). This is the early starters that were manufactured with the starter solenoid as a separate part. The ford tractor solenoid for this starter is part number D8NN11350CA, and is sold as a separate component.

This six(6) volts (V) gas tractor is mainly used on the 500, 600, 700, 800, and 900 series tractors.

Most of these starters are manufactured by Lucas, and there are two different starter solenoids that are available, namely the part numbers D7NN11390B, and the E4NN11390AC, with the latter being used on diesel engines only, and the former that can be used on a combination of gas or diesel engines.

Replacement starter drives units are sold separately, for either the 9 teeth or the 10 teeth ford starter drives.

Your Name (required)

Your Email (required)

Subject

Your Message